Jump to content

RB433AH PHY ERROR


batgoiko

Recommended Posts

Здравейте,

ползвам в домашни условия един RB433AH, от вчера започна да се рестартира постоянно, и на конзола "плюе" PHY ERROR

След търсене в интернет, прочетох че най често се получава от изгорял чип на суича IP175C.

Кажете къде бих могъл да го занеса борда да му сменят чипа ?

 

Благодаря предварително.

 

П.П. От София съм

Link to comment
Share on other sites

Благодаря за съвета.

6.3 волтовите кондензатори са сменяни, доколкото виждам, и изглеждат наред.

Напрежението върху С826 и С830 е 3.34 V, върху С841 е 2.66 V и върху С612 е 1.87 V, ако това би помогнало с нещо.

Ето това е лог-а на конзолата:

RouterBOOT booter 3.18

RouterBoard 433AH

CPU frequency: 680 MHz
  Memory size: 128 MiB
    NAND size:  64 MiB

Press any key within 2 seconds to enter setup..

loading kernel from nand... OK
setting up elf image... OK
jumping to kernel code
Starting...
Starting services...
MikroTik 6.23
router Login:

след това рестартирт и така до безкрай.

 

А като се опитам да го префлашна с нетинстал, картинката е следната:
 

RouterBOOT booter 3.18

RouterBoard 433AH

CPU frequency: 680 MHz
  Memory size: 128 MiB
    NAND size:  64 MiB

Press any key within 2 seconds to enter setup

RouterBOOT-3.18
What do you want to configure?
   d - boot delay
   k - boot key
   s - serial console
   n - silent boot
   o - boot device
   f - cpu frequency
   r - reset booter configuration
   e - format nand
   w - repartition nand
   g - upgrade firmware
   i - board info
   p - boot protocol
   b - booter options
   t - do memory testing
   x - exit setup
your choice: g - upgrade firmware

Upgrade firmware options:
   e - upgrade firmware over ethernet
   s - upgrade firmware over serial port
your choice: e - upgrade firmware over ethernet


PHY ERROR
trying bootp protocol.......

RouterBOOT booter 3.18

RouterBoard 433AH

CPU frequency: 680 MHz
  Memory size: 128 MiB
    NAND size:  64 MiB

Press any key within 2 seconds to enter setup..

loading kernel from nand... OK
setting up elf image... OK
jumping to kernel code
Starting...
Starting services...
MikroTik 6.23
router Login:
Edited by Mupo neTkoB
Link to comment
Share on other sites

След търсене в интернет, прочетох че най често се получава от изгорял чип на суича IP175C.

 

Правилно. Замяната с нов ще реши проблема.

Link to comment
Share on other sites

Правилно. Замяната с нов ще реши проблема.

Ще съм благодарен, ако споделиш къде в София биха могли да извършат тази дейност :)

Link to comment
Share on other sites

Сигурно във всеки сервиз. Въпроса е от къде ще намериш чип. Имаше колеги из форума които имаха. Поразтърси се.

Link to comment
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
  • Recently Browsing   0 members

    • No registered users viewing this page.
×
×
  • Create New...

Important Information

By using this site, you agree to our Terms of Use.