Jump to content

Излязла е нова версия на RouterOS v7.2.2


Recommended Posts

7.2.2 changelog:

*) bgp - added initial support for prefix limit;
*) bgp - improved stability when editing BGP template;
*) bonding - fixed LACP flapping for RB5009 and CCR2004-16G-2S+ devices;
*) ccr - added visible "passthrough" flag for interfaces on CCR2004-1G-2XS-PCIe;
*) ccr - usability and stability improvements for passthrough interfaces on CCR2004-1G-2XS-PCIe;
*) cd-install - allow selecting on which drive to install RouterOS;
*) conntrack - limited full Connection Tracking warning to 1 message per minute;
*) crs3xx - fixed storm rate on 1Gbps interfaces for CRS354 devices;
*) defconf - suggest user to set up new password;
*) dhcpv4-server - fixed minor logging typo;
*) fetch - improved full disk detection;
*) filesystem - fixed possible boot failure on RB850Gx2 and RB1100AHx2;
*) filesystem - improved long-term filesystem stability and data integrity;
*) gps - fixed minor value unit typo;
*) ipv6 - removed bogus commands from IPv6 neighbors menu;
*) l3hw - improved offloading for directly connected hosts on CRS305, CRS326-24G-2S+, CRS328, CRS318, CRS310;
*) l3hw - improved route table offloading for CRS317, CRS309, CRS312, CRS326-24S+2Q+, CRS354, CRS5xx, CCR2x16 devices;
*) leds - fixed ethernet LED behavior on wAP R ac;
*) leds - fixed wireless related LED behavior with WW2 package;
*) lte - added SMS sending support for MBIM protocol;
*) lte - added support for generic PXA1802 based modems;
*) lte - disabled wait for LTE auto attach;
*) lte - hide slave interfaces from export;
*) lte - improved stability when upgrading LTE firmware on Chateau 5G;
*) mlag - fixed MAC address moving between bridge ports;
*) mpls - do MPLS forwarding for nexthops without mappings;
*) mpls - fixed MPLS MTU and path MTU selection;
*) mpls - fixed MPLS forwarding after any interface configuration parameter is changed;
*) ospf - fixed GRE interface compatibility with OSPF;
*) ospf - improved stability when enabling or removing interface-template entries;
*) ovpn - fixed memory leak on TILE architecture;
*) ovpn - fixed packet processing on MT7621A;
*) ovpn - improved Windows client disconnect procedure in UDP mode;
*) ovpn - improved service stability when processing frequent disconnects in UDP mode;
*) ovpn - improved stability when forwarding traffic on TILE;
*) ping - fixed socket allocation after VRF change;
*) ppp - fixed "remote-ipv6-prefix" parameter unsetting;
*) ppp - fixed active sessions sometimes getting stuck;
*) ppp - fixed issue with multiple active sessions when "only-one" is enabled;
*) queues - improved stability in large list of queue scenarios;
*) rb5009 - fixed 10G linking issues with Intel X520, XXV710 NICs;
*) route - fixed "table" menu emptying after RouterOS upgrade;
*) route - fixed static routes in VRF becoming invalid after reboot;
*) route-filter - fixed community matchers;
*) rsvp-te - improved stability when "Resv" received for non-existing session;
*) supout - added RIP section;
*) system - fixed IP service initialization in VRF after system startup;
*) system - fixed rare partial loss of RouterOS configuration after package upgrade/downgrade/install/uninstall;
*) torch - properly capture all related IPv6 traffic;
*) upnp - improved stability when processing incomplete HTTP header;
*) vpls - fixed "pw-l2mtu" parameter usage;
*) vrf - fixed VRF leaking;
*) winbox - do not show "unknown" area under "Routing/OSPF/LSA" menu;
*) winbox - do not show type value for NXDOMAIN entries under "IP/DNS/Cache" menu;
*) winbox - made "Interface Templates" table sortable under "Routing/OSPF" menu;
*) winbox - properly clean up SFP module information after it is unplugged;
*) winbox - properly clean up disk after a failed file upload;
*) winbox - show PVID column by default under "Bridge" menu;
*) wireless - fixed EAP-TLS authentication;
*) wireless - fixed GUD version in 3gpp information;
*) ww2 - fixed VLAN tag handling;
*) x86 - improved support for i40e driver;
*) x86 - improved support for Intel E810 NIC;

Свали от тук

Link to comment
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now

  • Recently Browsing   0 members

    • No registered users viewing this page.
  • Create New...

Important Information

By using this site, you agree to our Terms of Use.